Showing results: 286 - 300 of 452 items found.
-
Fiaxell Sàrl
When long term electro-chemical tests (>1000 hours) are run to monitor the cell degradation at the cathode for example, it is important to avoid any contaminant in the gas flow rate.Inconel 601 flange equipped with alumina housing and alumina tube to feed the gas to the electrode during long term test (>1000 h)Typical poisoning is coming from the chromium contained in the steel tubing. The volatile chromium species (Cr6+) will flow into the cathode (with the air) and thanks to the intake of electrons at the electrode, the chromium ion will transform to chromium oxide and be deposited at the cathode triple point. In such a case, the long term test kit is used. The Inconel 601 flange is equipped with an alumina housing (>96 % Al2O3) and the air (or other gas) is led through an alumina tube. The long term test kit is fully compatible with other functionalities proposed with the Open Flanges™ test Set-Up as the integrated steamer or the small pellet test kit. The long term test kit can be implemented on the fuel, on the air or on both sides.
-
ESFP280 -
Optellent, Inc.
The OPTELLENT ESFP280 is a cost-effective and convenient test board for testing SFP/SFP+/SFP28 optical transceivers in R&D and manufacturing environments. The ESFP280 is equipped with high quality RF connectors for data signals and test points for low frequency control and status signals. The ESFP280 is equipped with power supplies to enable voltage margining. Key status signals are displayed using LED indicators.
-
KT-96A -
KILTER ELECTRONIC CO.,LTD
LCD Max. Indication 3999,with length unit. Locate the broken point of a cable. With RS-232 interface, it can be connected to your computer. Takes a new ¡°VECTOR MEASUREMENT¡± technology in measuring the length of the cable. Length Test Range:400m/4000m/40km. Accuracy: ¡À1% rdg ¡À 0.3m. For use in computer network, CATV, communicate engineering. With Volt, Resistance,continuity,diode test
-
National Technical Systems
Differential scanning calorimetry (DSC) measures Specific Heat Capacity, Heat of Transition, and the Temperature of Phase Changes and Melting Points. DSC measures the rate of heat flow, and compares differences between the heat flow rate of the test sample and known reference materials. As a sample undergoes a transition (melting, crystallization, etc.), heat is absorbed or emitted. This change in heat flow is then measured by the system and can be analyzed. The difference determines variations in material composition, crystallinity and oxidation.
-
TÜV SÜD Japan
SAR limits are there to protect all of us from wireless devices that exceed the transmit Radio Frequency (RF) threshold. SAR stands for Specific Absorption Rate. It's a measure of the rate at which energy is absorbed by your body when you are exposed to an RF electromagnetic field. In some countries, the SAR test result figure has to be displayed at the point of sale. To have a presence in these markets, your products must meet strict SAR regulations.
-
LXinstruments GmbH
The relational test database is the pivotal point of the software structure. On one hand, this is where the test applications and test systems used for productive testing are stored; on the other hand, it provides the storage space for all DUT-related test data. Depending on customer requirements, the test database may either be hosted locally on the test system or centrally on a server, supporting several test systems. The database performance is sufficient for a high-volume production environment with many test systems which access the central database in parallel. LXinstruments prefers to implement the database as a license-free MySQL database; it is however also possible to realize a version based on Microsoft SQL.
-
Parrot Invent
Multimeter Test Probes, Voltmeter test leads,with the Parrot™ Clip Invention provide precise, HQ, accurate, reliable contacts and connections. Parrot™ Clips with HQ leads and banana plugs or other connectors are the best solution for DDM, analog multimeter for high voltage measurements as well as for high current measurements. Measurements with multimeter test probes require both: Hands-on direct point contact and grip on, Hands free removable connection.
-
Pilot 4D M4 -
SEICA SpA
The Pilot 4D M4 is a full-performance, double-sided, flying probe test system with an extremely high level of flexibility, making it the ideal solution for those with a wide variety of testing needs, from prototypes to small/medium production volume, through the repair of field returns and reverse engineering. The vertical, compact architecture and the excellent board clamping system ensure that there is no oscillation of the board under test, which in turn greatly facilitates the precise positioning of the probes on the test points.
-
Garland Technology
Passive network test access points (TAPs) are a hardware tool that allows you to monitor your network. Garland Technology offers fiber network TAPs in network speeds of 1Gb, 10Gb, 40Gb and 100Gb. Fiber Network TAPs are passive, purpose-built hardware devices that make a 100% copy of your networks data - without affecting network traffic. Passive network TAPs let your monitoring tools to see every bit, byte and packet®.
-
Sparling Instruments
Measures accurately over a flow range of 10:1 or greater.± 2% of rate accuracy, guaranteed by certified wet calibration at three test points in.Sparling’s National Institute of Standards and Technology (NIST) traceable hydraulic flow lab.Sturdy cast or fabricated steel construction.Operating temperatures are over 100° F(unless higher temperature construction is specified).Suspended solids are over 0.5% of volume.Easily maintained with standard tools.Registration can be furnished in any standard Engineering Unit.
-
Instron
Instron load cells are an integral part of the load weighing system of a testing machine. Their interchangeability along with transducer recognition and single point electrical calibration makes them easy to use. They maintain high alignment and are resistant to offset loading throughout the test, even with large sized specimens. Instron controls the design, manufacture and quality of all load cells, with customer applications in mind. They are certified in accordance with international standards for use in material testing machines only.
-
LD-LOSM-A10 -
Labodam
OsmometerLD-LOSM-A10is colorful LCD touch display with sample size 50 μl to 100 μl and measuring range up to 0 to 3000 mOsmol /kg H2O at ambient temperature 10 to 30°C. Features with on-screen display of molar concentration, freezing point, and osmolarity. At very low testing time it provides fast and accurate osmolality test results. Applicable in General medicine, Routine and research, Forensic medicine, Electron microscope.
-
2000A -
SCR ELEKTRONIKS
SCR ELEKTRONIKS have developed “TEMPERATURE RISE TEST BENCH FOR MEDIUM VOLTAGE SWITCH BOARDS” to measure rise in temperature at various points as mentioned in standard at junctions. The set-up consists of a True RMS Constant Current Source (to maintain the Current within + / - 1 % of set value with Digital Indication), PC based control system, Temperature data logging on PC, Servo-Controller and other indications. Digital voltmeter Primary Voltage) indicates the position of auto transformer (variac).
-
NOVOTEST TP-1M -
NovoTest
Portable Coating Thickness Gauge NOVOTEST TP-1M – device for operative non-destructive measuring of coating thickness in compliance with ISO 2808 with high measurement accuracy.Coating thickness gauge is designed to test:thickness of various thick protective coatings on various metals and alloys;thickness of paint and other dielectrics – radioabsorbing, mastic, teflon, plastic, electroplating coatings on steel;thickness of electroplating and paint coatings on non-ferromagnetic alloys and non-ferrous metals;thickness of bitumen and other thick coatings on various metals and alloys;as well as relative humidity, air temperature, surface temperature, dew point temperature and difference between surface and dew point temperatures, estimate the depth of grooves and the surface roughnessElectronic thickness gauge – device which widely used in shipbuilding and automotive industries for measuring of the thickness of paint, in order to test the quality of products, also it used for determining technical condition of the tested objects.
-
NOVOTEST TP-1 -
NovoTest
Portable Coating Thickness Gauge NOVOTEST TP-1 – device for operative non-destructive testing of coating thickness in compliance with ISO 2808 with high measurement accuracy.Coating thickness gauge is designed to test:thickness of various thick protective coatings on various metals and alloys;thickness of paint and other dielectrics – radioabsorbing, mastic, teflon, plastic, electroplating coatings on steel;thickness of electroplating and paint coatings on non-ferromagnetic alloys and non-ferrous metals;thickness of bitumen and other thick coatings on various metals and alloys;as well as relative humidity, air temperature, surface temperature, dew point temperature and difference between surface and dew point temperatures, estimate the depth of grooves and the surface roughnessElectronic thickness gauge – device which widely used in shipbuilding and automotive industries for measuring of the thickness of paint, in order to test the quality of products, also it used for determining technical condition of the tested objects.
